FRONT INNER NOSE STRUCTURE

Just purchased my new inner nose structure (headlight support bracket) from Wolfsburg West. I should have by the end of the first week of the new year. After this, I will have all the parts to completely build the front section back to good.

Happy New Year All!

Front Nose Clip Repair - Part #2

 I used a plasma cutter to remove the front headlight support bracket.  I guess it was from being lazy or just frustrated with removing the inner valance off of the frame.  I've fabricated a new replacement for the section that I quickly cut out.  For some reason, this still seemed a lot simpler.  This was done on both sides of the van.  I am currently awaiting my order for a new headlight support bracket. I just need to grind it down once a few places are tack-welded to the body.  This piece is required to spot-weld the inner valance to the body, so I must put it back.  I'll show this completed, but I will only continue after I have the replace support bracket in my possession to try it on for size.

 Just making sure that I am going in the correct direction with the fender and pillar from the size perspective. It doesn't completely line up yet because I have not grind-ed down the tack-welds for the side rocker panel that I repaired previously. This is just to check to see if the angle will be right when I hit that step soon.  This should be completed in a few weeks.

Although, the valances does not fit onto the frame, because of metal that still needs to be clear off the two frame post.  I had to try it partly on to make sure the part's location is exactly where I expected it. This is an AutoCraft part, so it is very proper.  Stay tuned.

You can watch this video to get a full status of what I've just discussed:

Dirty Steering Box

I've had this bus for about 1 year or so and I never looked completely under the front or the memories of this sight must have been stored outside of my mind.  It is disgusting and looks like some type of life is being incubated inside of there.  The question is, how does one begin to clean this thing?

Nose and A-Pillar replacement

My prep to fix the front noes of the bus.  Here I measured the replacement panel that will repair the crushed bus nose shape.  The panel that I cut is 8 inches (20.32 cm) high. The replacement panel is it a tad bit higher, but I rather grind it up to cover my imperfect cuts that normally run a bit high and low. I used the blue tape as a guide, trying to cut on top of it, or skimming it.  With all the sparks, it is very hard to tell. That is why I made sure that I under cut the piece. If I made a mistake, the whole replacement would be roughly $600.00 USA with shipping and it would require my retro-fitting the earlier bullet turning signals.

The bottom nose was removed. I tried to input the replacement part and as expected, it is to low to insert.  The main goal of this repair is to replace the A-Pillar below the floor.  I needed access to see what was beneath it all.  The secondary reason was to replace the damaged nose.


Please stay tuned..

Nose and Valance Removal - updated

In this photo, 8" inches of the noes has been removed to fix a few crushes  along the driver's headlight and the point in the center was banged in pretty badly. A former own drilled a lot of small slide-hammer holes to try to pull the tip out.

 I removed most of the outer front nose panel skin from the heavily rusted and bent out of shape inner valance.  The target is to remove the inner valance and headlight support bracket.

Exposed is the headlight support bracket on the top and the inner valance at the lower half. This is before the removal.

Side view of most of the inner valance removed. The hard part is removing the part in which it is connected to the frame. I'm am going to finish removing the headlight support bracket so that getting to the top of the beam would be simpler.

Front view of the removal.  I mostly used a plasma cutter to remove most of the metal and a cutoff wheel when control was required.

Here is all the scrap removed.  Stay tuned.











Getting the bottom valance off the bumper support beams is not an easy task.  After another 2 hours, i'm basically still in the same situation.  In this photo below, I removed 80% of the metal off the bumper support beam and I have the headlight support bracket detached from the passenger's side. I've decided to remove it to have access to straighten it out. It had been impacted by the minor accident.

Nose reconstruction project.

I just purchased a new inner valance for my bus project.  I have been reading up on how to install it. It seems pretty straightforward and scary. Hehehe.. I've also, purchase lower A-pillar post to assist in alignment of the whole setup. Stay tune for that process which will begin shortly.  I am not going to add the fenders until I have had a chance to work both sides of the door post (A-Pillar on the passenger's side).




Here is a photo of my current front under the nose clip. Doesn't look good. the previous owner had damage and popped holes into the front. The holes allowed moisture to get in causing this amount of rust.  This will all be replaced and made to look new. The mini project will be called the VW Bus Nose Surgery project (Front Inner Valance).

Rusty front

Closing Crap up! - Updated

I had to go a little medieval to get the side rocker panel in place, bending the B-pillar closeout plate with my Ford's scissor jack . It worked perfectly. The top lip of the outer rockers had about 1/8 of space that needed to be balanced out.   See the next photo and you'll understand that it was indeed successful.

As you can see, the panel lined up beautifully.  I've added the tack welds to hold the panel in place and I also added a few spot welds to the bottom to keep it in.  I ran out of gas today for my MIG welder.  Picking some up tomorrow and finishing the closing.

Here is the side bead welded across and down. The warpage was minor for such a long piece of metal. I had to jump around the line so that one part of the metal did not become too hot at anytime.  Just need to grind down the slug and prep area for priming.

Major Progress

 It's been a long time. A lot of my slow speed comes from mistakes and the lack of confidence.  I believe, once I finish this area, things will speed up, as I am already feeling my confidence building up nicely. The way in which I tackle each problem is only creating a stronger Marquis at the end of each session.

I finally got the B-Pillar closed up and sealed perfectly.  I ended up switching from the AutoCraft parts to a Funky Green panel pillar.  This pillar reaches farther up and it also closes the gap perfectly.

Once the  B-Pillar closed up,  I spot welded  the inner rockers to the cross connects (top and bottom hats). In some cases, I had to use a MIG welder to spot weld behind the middle pillars. For the ones that were reachable, this spot welder was the fastest and cleanest method possible.

This is a photo that shows how I tried to access in the middle of the beam with the spot welder.  In most cases, I didn't work well.  I was tired of holding the welder since it is very heavy.

The inner rocker and the pillar and the pillar closeout plate looks solid. I've added some weldable primer to resist against rust that could form when closing the gap and from the welding process overall.

The outer rocker is finally sized up for the final time to make sure it lines up for welding. I need to purchase a few more magnets to make sure all areas along the panel mates the original across the van in a leveled way.

I will post pictures when I am finished with the welding of the side.

Funky Green Panel sizing - B Pillar

This is a video moment of the installing the Funky Green Panel - B Pillar.  I promise this will end soon. :-)

Metal Prep - Video Part 1

Here is the metal prep for my damage front nose cone (panel). The process takes 5-6 weeks to remove rust.  So, this is Part #1

The Funny Green Panel vs AutoCraft

I am setting up the Funky Green Panel - B pillar, as the one from AutoCraft had a lot to be desired. It did not close properly and it also did not come with a block-off plate. Here I am sizing up my cuts before I begin to weld this piece in.  I will also check the block-off and make sure the outer rocker panel will close properly. The block-off plate that I tried to fabricate did not allow the outer rocker to close as it did not have the right curve in the right area. My piece was pretty good, but for $40 for both parts, why do this? With the AutoCraft piece, you have no options, as the part showed in this photo comes alone.

I have a weird cut, as I want the piece to lock vertically and horizontally.  More importantly, it has the standout tab to mount the  block-off plate to it at the top, which I am heavily modifying to fit with my Dremel.  The next photo will show the 1/4 of an inch that I'll have to raise it to. The bottom piece must completely clear the bottom lip of the inner rocker so that the outer rocker could sufficiently close.  Please see my next photo.

As you can see, the clearance is not quite there.  I will be back in the shop this weekend to complete this fitting session.  Before then, I'll complete the inner rocker welds.  This is all taking a long time as I am learning and I am learning that not all replacement parts are created equal. The outer rocker was purchased from AutoCraft and I must say, that it is awesome. So, this discussion is not to say AutoCraft is inferior, but we have to use the best part for each application.














Funky Green Panel vs My Fabricated versions.  I was pretty good.. :-)  The only real problem was the B-Pillar didn't allow the outer rocker to close. This could be because of the accident.  The Green one just fits much better.

The Front Nose - Damage

(p1)

(p2)

 I purchased a new 8 inch nose replacement panel to repair the center nose that normally gets smashed in at some point by some driver poor at parking. This is the Green Stuff.  It comes with a weld-thru green primer to prevent corrosion.

This is a very used front nose panel that I purchased online (p2). The unit was advertised to be used as wall-art, Go figure!  Who in the hell would use a split bus nose as wall-art?

Anyway, I had other intentions for it. I needed the section to the left of the light bucket and to the right of the bucket (p5).  The area to the right of the bucket, on my current nose was damaged (as seen in p1). The complexity of the curve didn't allow for me to straighten it out by a stud hammer. So, rather than using filler like how it was originally setup, I'll cut it out and replace it with the downer.

(p3)

I had to remove the rusty bottom, it bothered me greatly, even though, it was not my area of interest. By blocking out the areas that I want to protect with a marker, I let the cutting begin. Please see my cutting videos at the end of of this section.

(p5)

(p4)

Photos p4 and p5 shows the downer areas sized up to the location in which they will be graphed. I will attempt to repair the left-side of the light bucket with a hammer and dolly before cutting it and replacing the sheet metal.

Please see videos on the next page ->

Step-up my game..

I've had this VW Bus for 1 year now.  I really need to step-up my game. By summer, I promise to have it in painting mode.  Thank god for having this blog, it helps me keep track of time.

Nose Clip Repair Plan

I have it traced out where I am going to remove the damaged area.  Before, this was filled in with filler and I tried pulling it out with a stud hammer. Because the area has a rather complex cure, the metal is not very malleable. None of the stud hammering pulled any part of it out. I will cut this part out and patch in a replacement.

I found this rather crude organ downer online. It was cheap, because it is pretty rusty, but the part I need is OK. I wish under the eye wasn't so jacked up as I would have liked to pull the who area, but once I have the cut open, I'll be able to work on the other part with a hammer and dolly.  I'll also have to pull out a small 5"x5" patch on the passenger's side.  It is not shown in the above picture, but there is a small rust hole there.

 I've also found online a nose clip that I can replace the smashed up nose area of the bus. This will handle the bang in the front.  This project will begin when I close up the side. I'll start cleaning up the downer part when I have a moment before, As I want to reduce the big elements in my garage. So I am going to do most of the cutting this weekend.

The inner rockers are permanently welded in. I had to remove them and straighten back out the metal, as I welded it too forward the first time. I was going to order a new one, but I thought it would be a better exercise if I fixed what I destroyed to help keep my cost down and save time waiting for the new part to come in.  Also, I've welded in the b-pillar post cover that I also had to re-work.  Hey!  I'm learning the hard way, but it is learning indeed.   I still have a question posted on a forum on how to handle the tab down on the bottom left.I believe it has to be bent over and weld closed. If I don't get a response, I'll take a look at the other side

Here is the outer rocker mating up to the B-pillar post that I fabricated. I'll have to grind down some of the arch, as it doesn't allow for my tack-weld holes to line up.  These wholes were made with a flange tool. The reverse side allows you to punch holes into sheet metal like paper. It works with a compressor. Please see the photo at the very end.

Along the top side panel, I'll have to grind down some of the ridges that doesn't allow the outer rocker to mate evenly to the bottom. This doesn't allow the weld holes punched in the bottom to mate to the inner rocker.  This will be fixed on my next visit to the garage.

Here is how the side rocker panel looks when mated up. As you can see, this will look pretty good once welded in. This will start next weekend.  I got an immunization shot on Saturday that made me feel pretty sick, so I had to stop.

Fixing the front B pillar post

 After trying to weld the beotch to non-weldable primer, I finally got it straightened out. This piece was fabricated in-house, as no suppler carries the B pillar cover.

 Not the best looking welds in the world but they are holding after I removed the primer and tack welded the plate in.  I've wire brushed the welds and the next photo will show it in primer.

Next I'll just have to grind down the welds so that I can close up the side rocker panel. I primed it up so it doesn't rust over the week, until my next time in the show next weekend. This is weldable primer, so that any touch ups can just be cleaned and welded.

Before and after

This picture, I was finished trying to repair the inner rocker. As you can see, after trying to weld in some metal over rusted parts, I cutaway a piece because I realized it should be completely replaced.

Here is the inner rocker being size up for welding. The small weld holes have been drilled in (not in this picture) and ready for welding in.  I just need to make sure the side by the dog leg can be closed up right.

My 58 VW Bug

Thought I should post a picture of my 1958 VW Bug that was in the Gov Island Show in 2013.  I missed the show this year.  I now this is off topic, but often I forget that I have this car because I am working on the Bus so often.

Labor Day Week-end with the Bus.

I've partially installed the new jack port under the drivers'side rear.  This is weld-thru primer, so that it would not rust while I am tackling other small jobs. I am sort of running low on argon/CO2.

 This is the inner wheel well that I am patching in. The original one was rusted and it is easier to replace complete, rather than trying to cut out a lot of small little patch sections. The piece is tacked in, secured and ready for full welding on the next weekend.

 Here is the side view of the work to be done.

 Again, making sure the inner rocker fits well before I progress to the next stage.  I'll just need to remove the rust under the cargo floor and pop in some spot weld holes on the top of the inner rockers.

 I have the replacement (driver's side) B-pillar welded in on the driver's side. So far, this all looks good.  I'm looking for a way to deal with the A-Pillar before I work on the dog legs.